Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Iredell County · 1 hr from Greensboro

Trail Cutting for Statesville & Iredell County

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

Wooded land in Statesville is a lot more fun with a trail through it. A&R Land Services cuts walking loops, UTV paths and equipment lanes across Iredell County with a forestry mulcher, leaving a chip floor you can ride the same day. We're about 1 hour away in Greensboro.

Nearly every trail we cut in Iredell County crosses a creek or a wet-weather branch. On Statesville properties we place the crossing where the bottom's firm, keep the clearing narrow inside the buffer, and set stone or a culvert if you'll be driving it in the wet.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Statesville ground conditions and how they shape trail cutting

Iredell County runs its own erosion and sediment control program with the one-acre threshold, and the South Yadkin and Lake Norman watersheds carry stream buffers. The soil is what dictates the calendar. We don't run heavy grading on the Iredell and Enon belts until they've had a dry spell; we mulch on the Cecil ridges while we wait. Diabase boulders are a given in trenches and footings on the dark-soil ground, and we probe every pad.

Around Lake Norman State Park, Harmony and NC-115, the properties we're usually called to look like this:

  • Former dairy and row-crop farms along I-40 and I-77 being cleared and rough graded for industrial parks and subdivisions
  • Builder lots in the new neighborhoods between Statesville and Troutman needing lot clearing and pad prep
  • Pole barn pads, farm roads and gravel drives on working farms across the county

What trail cutting jobs look like around Statesville

If you're near NC-115 or Statesville Regional Airport, odds are your situation is one we've already worked: former dairy and row-crop farms along I-40 and I-77 being cleared and rough graded for industrial parks and subdivisions, or connecting a house to a creek, pond or picnic spot through the woods.

The trail cutting approach for Iredell County ground is the same either way — look first, quote in writing, bring the right attachment, walk it with you when it's done.

Neighbors in Mocksville, Elkin and Mooresville call us for the same work; Statesville sits right in the middle of that route.

Why Statesville property owners call A&R

Greensboro to Statesville is about 1 hour, which keeps a half-day trail job worth doing and makes it easy to come back and add a loop or a spur later.

Send us an aerial with the route sketched in and a couple of photos of the woods. We'll give you a real number for cutting it in Statesville.

Trail Cutting in Statesville: questions

How much does it cost to cut a trail through the woods?

Trails are priced by length, width and how thick the woods are, with creek crossings and gravel as the add-ons. A quarter mile of walking path through open hardwoods is a short day. A mile of ten-foot UTV loop through privet with two creek crossings and gravel on the climbs is a multi-day job. We flag the route with you and give a written number. Estimates are free.

Will the trail turn into mud?

Not if it's routed right. A trail that runs straight down a slope on Piedmont clay becomes a gully; one that follows the contour and crosses slopes at an angle sheds water. We route for drainage, keep the mulch layer on the path, and put gravel on any stretch that's going to be wet no matter what — usually creek approaches and the bottom of climbs.

How far is A&R Land Services from Statesville?

We're based in Greensboro, about 1 hour from Statesville. Iredell County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near Lake Norman State Park and Harmony?

Yes. We work throughout Statesville and the surrounding Iredell County area, including properties around Lake Norman State Park, Harmony and NC-115. If you're outside the town limits, send the address and we'll confirm it's in range.

What does trail cutting typically involve on a Statesville property?

Walking and running loops on wooded homesites is the most common version of it around Statesville. Creek crossings get stone or a culvert if scoped. Wet stretches and climbs get gravel if you want them drivable year-round. We make a final pass to knock stubs flush and leave a clean mulch floor. Gravel on climbs, wet stretches or the whole trail is the factor that moves the price most on Iredell County jobs, and we'll walk through it with you on site.

Trail Cutting in Statesville, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate