Wooded land in Walkertown is a lot more fun with a trail through it. A&R Land Services cuts walking loops, UTV paths and equipment lanes across Forsyth County with a forestry mulcher, leaving a chip floor you can ride the same day. We're about 28 minutes away in Greensboro.
Nearly every trail we cut in Forsyth County crosses a creek or a wet-weather branch. On Walkertown properties we place the crossing where the bottom's firm, keep the clearing narrow inside the buffer, and set stone or a culvert if you'll be driving it in the wet.



Walkertown ground conditions and how they shape trail cutting
Walkertown is on the northeast side of Forsyth between Winston-Salem and Belews Lake, on rolling Cecil and Appling clay with Wedowee on the sandier knolls. Salem Lake sits on its southwest edge and the whole southern part of town drains to it, which puts those parcels under Winston-Salem's water supply watershed rules. To the north the ground tips toward the Dan River basin and Belews Creek. This was tobacco and small-grain land, and the grown-up allotments are loblolly and sweetgum with privet, honeysuckle and poison ivy thick along every old fence row.
Around NC-66, Baux Mountain Road and Main Street, the properties we're usually called to look like this:
- Horse and small cattle operations reclaiming pasture from privet and sweetgum
- Subdivision lots along US-158 and NC-66 needing pine cleared and pads leveled
- Shop pads, gravel lanes and garden plots behind existing homes
What trail cutting jobs look like around Walkertown
Around Main Street, the properties that call us for trail cutting tend to be horse and small cattle operations reclaiming pasture from privet and sweetgum.
Closer to Walkertown Community Park it's more often fire and emergency access through dense acreage — different layout, same machine, and the estimate reflects the difference honestly.
Walkertown isn't one kind of ground, and we don't price it like it is.
Neighbors in Kernersville, Belews Creek and Rural Hall call us for the same work; Walkertown sits right in the middle of that route.
Why Walkertown property owners call A&R
Greensboro to Walkertown is about 28 minutes, which keeps a half-day trail job worth doing and makes it easy to come back and add a loop or a spur later.
Send us an aerial with the route sketched in and a couple of photos of the woods. We'll give you a real number for cutting it in Walkertown.
Trail Cutting in Walkertown: questions
How much does it cost to cut a trail through the woods?
Trails are priced by length, width and how thick the woods are, with creek crossings and gravel as the add-ons. A quarter mile of walking path through open hardwoods is a short day. A mile of ten-foot UTV loop through privet with two creek crossings and gravel on the climbs is a multi-day job. We flag the route with you and give a written number. Estimates are free.
Can you cut a trail across a creek?
Yes. We pick the crossing where the banks are low and the bottom is firm, keep the clearing narrow inside the buffer, and either set stone for a ford or install a culvert with fill over it, depending on how much water runs and how often you need to cross it in the wet. The excavator and the dump trailer handle it on the same visit.
How far is A&R Land Services from Walkertown?
We're based in Greensboro, about 28 minutes from Walkertown. Forsyth County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle trail cutting near NC-66 and Baux Mountain Road?
Yes. We work throughout Walkertown and the surrounding Forsyth County area, including properties around NC-66, Baux Mountain Road and Main Street. If you're outside the town limits, send the address and we'll confirm it's in range.
What should I expect from a trail cutting job in Forsyth County?
UTV, ATV and dirt bike trails on recreational land is the most common version of it around Walkertown. A written plan with the trail's length and width, where crossings are, any gravel or culvert work included, and the price. Trails are quoted by the job after the walk. Trees on the route that need felling and handling is the factor that moves the price most on Forsyth County jobs, and we'll walk through it with you on site.