A&R Land Services installs gravel driveways in Graham — from the NCDOT permit question at the road to the last pass of the blade at the garage. We're only about 30 minutes from Graham, which matters on a job that moves this much stone.
A lot of Graham lots are wooded right to the road, so the driveway starts with clearing. We mulch the route, pull the stumps, and the chips go to the sides as erosion control while the roadbed is cut. It's one mobilization from Greensboro instead of a clearing contractor and then a driveway contractor.



Graham ground conditions and how they shape gravel driveways
Graham is the Alamance County seat and sits just south of Burlington on the same tough ground — Enon, Iredell and Mecklenburg clays over diabase, with Cecil on the higher ridges. The Haw River runs along the east side of town with Big Alamance Creek and Back Creek feeding in, and the bottoms along them are Chewacla silt that floods. Graham-Mebane Lake on Back Creek is the town's water supply. Old fields come back as loblolly, red cedar and sweetgum, with privet, honeysuckle and Bradford pear filling in along the roads.
Around Big Alamance Creek, Graham-Hopedale Road and Swepsonville Road, the properties we're usually called to look like this:
- Flat Iredell clay fields that need ditching and swales before they'll carry hay equipment
- Subdivision lots and small commercial sites along the I-40/I-85 and Graham-Hopedale corridor
- Fence-row and hedgerow clearing on old farms where the wire has disappeared into honeysuckle
What gravel driveways jobs look like around Graham
Most of our gravel driveways work in Graham comes from two directions. First, flat Iredell clay fields that need ditching and swales before they'll carry hay equipment. Second, second entrances and access lanes to outbuildings.
Both show up regularly along Swepsonville Road and NC-87, and both are jobs we can usually walk, quote and schedule inside a couple of weeks.
If you're just outside Graham — Gibsonville, Elon, Mebane or anywhere between — you're still inside our regular range.
Why Graham property owners call A&R
On a Graham driveway job the owner is the operator. Clark — veteran, firefighter — walks the route, writes the estimate and runs the machine that cuts the grade. What was discussed is what gets built.
Reach out to A&R Land Services for gravel driveway installation anywhere in Alamance County — new entrances, long drives, construction access and everything between.
Gravel Driveways in Graham: questions
What kind of gravel is best for a driveway in North Carolina?
ABC crushed stone, also called crusher run, for the base and often for the whole driveway. It's a mix of angular rock and stone dust from the local quarries that compacts into a hard, water-shedding surface. #57 stone on top gives a cleaner look but stays loose and rolls underfoot. Pea gravel and river rock look nice and don't lock together at all — avoid them on anything with a slope.
How much does a gravel driveway cost in NC?
Length and base depth drive it. A short, flat driveway on firm ground with a modest base is the least expensive; a long drive through woods with a cut-and-fill grade, a culvert, fabric over soft ground and a thick base for truck traffic costs several times as much per foot. Stone is sold by the ton and a driveway takes a lot of it, so distance from the quarry matters too. We quote per job after walking the route — the estimate is free.
How far is A&R Land Services from Graham?
We're based in Greensboro, about 30 minutes from Graham. Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle gravel driveways near Big Alamance Creek and Graham-Hopedale Road?
Yes. We work throughout Graham and the surrounding Alamance County area, including properties around Big Alamance Creek, Graham-Hopedale Road and Swepsonville Road. If you're outside the town limits, send the address and we'll confirm it's in range.
What should I expect from a gravel driveways job in Alamance County?
New homes, shops and barns on rural lots is the most common version of it around Graham. Trees and brush on the route get mulched or grappled, stumps come out, and the roadbed is cut to grade with crown and ditches. Soft spots are excavated and fixed. Culvert size and whether an NCDOT permit is required is the factor that moves the price most on Alamance County jobs, and we'll walk through it with you on site.