Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Drainage & Erosion · Alamance County · 30 min from Greensboro

Graham Culverts

Driveway pipe sized to the water, set to grade, bedded in stone — no more washed-out entrance.

A driveway entrance in Graham is only as good as the pipe under it. A&R Land Services installs and replaces culverts throughout Alamance County — new entrances, crushed pipe, undersized pipe that backs the ditch up — and we set every one to grade on stone bedding so it stays put. We're about 30 minutes away in Greensboro.

Alamance County ditches carry more water than people think. A roadside ditch below a wooded hillside or a pasture can fill a 15-inch pipe in a thunderstorm, and that's when the entrance goes over the drive. We look at the drainage area above your Graham driveway before we pick a pipe size.

Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes
Freshly cleared and rough-graded backyard lot with track marks, mature trees left standing beside a house
Backyard lot cleared and rough graded, shade trees kept

Graham ground conditions and how they shape culverts

South of town the land stays rural a long way toward Snow Camp and Saxapahaw, and that's where most of our Graham work is: twenty- to eighty-acre cattle and hay farms off NC-87, NC-49 and Swepsonville Road where pasture is being taken back from cedar and privet, fence rows are being cut out, and farm roads are going in. Closer to I-40/I-85 and the Graham-Hopedale Road corridor it's subdivision lot clearing and small commercial site prep. The Haw River frontage near Swepsonville and Saxapahaw has brought in some river-lot cleanup and trail work.

Around Big Alamance Creek, Haw River and Graham-Mebane Lake, the properties we're usually called to look like this:

  • Subdivision lots and small commercial sites along the I-40/I-85 and Graham-Hopedale corridor
  • Fence-row and hedgerow clearing on old farms where the wire has disappeared into honeysuckle
  • Flat Iredell clay fields that need ditching and swales before they'll carry hay equipment

What culverts jobs look like around Graham

Around Graham-Mebane Lake, the properties that call us for culverts tend to be subdivision lots and small commercial sites along the I-40/I-85 and Graham-Hopedale corridor.

Closer to NC-87 it's more often crushed, rusted or collapsed driveway pipe replacement — different layout, same machine, and the estimate reflects the difference honestly.

Graham isn't one kind of ground, and we don't price it like it is.

If you're just outside Graham — Burlington, Saxapahaw, Mebane or anywhere between — you're still inside our regular range.

Why Graham property owners call A&R

Being about 30 minutes from Graham means a culvert replacement is usually a single-day trip for us, not a two-day mobilization. That shows up in the price, and it means we can get to a washed-out entrance quickly after a storm.

For culvert installation and replacement in Graham and the rest of Alamance County, call (336) 392-8138. Free estimates, properly sized pipe, and an entrance that holds.

Culverts in Graham: questions

Do I need a permit to put a culvert in my driveway?

If your driveway connects to a state-maintained road, yes — NCDOT requires a driveway permit for a new entrance or a changed one, and the district office will specify the pipe size and length. There's generally no state permit for culverts on private roads or interior farm lanes, though stream crossings can trigger buffer rules. We'll tell you which situation you're in.

How much does it cost to install a driveway culvert in NC?

The main drivers are pipe size and length, whether an old pipe has to come out, and how much stone the backfill and end treatments take. A short 15-inch HDPE pipe on a private drive is a half-day job. A 24-inch, 40-foot pipe on a state road with riprap ends and a full ditch reshape is a bigger day with a lot more material. We give a free written estimate after seeing the site.

How far is A&R Land Services from Graham?

We're based in Greensboro, about 30 minutes from Graham. Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle culverts near Big Alamance Creek and Haw River?

Yes. We work throughout Graham and the surrounding Alamance County area, including properties around Big Alamance Creek, Haw River and Graham-Mebane Lake. If you're outside the town limits, send the address and we'll confirm it's in range.

How do you approach culverts on Graham ground?

Farm lane and trail crossings over ditches and draws is the most common version of it around Graham. Pipe size and material, length, end treatment, stone quantity and how the drive gets tied back in. If an old pipe is coming out, the estimate covers removal and disposal too. Pipe diameter and length — larger pipe costs more and moves more dirt is the factor that moves the price most on Alamance County jobs, and we'll walk through it with you on site.

Culverts in Graham, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate