A&R Land Services is a veteran and fireman owned crew trenching for utilities and drain lines in Graham and the rest of Alamance County. Right depth, straight run, laser-checked fall on drains, and a backfill that doesn't sink.
Drain lines in Graham yards need fall, and clay doesn't forgive a flat spot. We check the trench floor with a laser on every drain run in Alamance County so the water actually reaches daylight instead of sitting in a low point in the pipe.



Graham ground conditions and how they shape trenching
Graham is the Alamance County seat and sits just south of Burlington on the same tough ground — Enon, Iredell and Mecklenburg clays over diabase, with Cecil on the higher ridges. The Haw River runs along the east side of town with Big Alamance Creek and Back Creek feeding in, and the bottoms along them are Chewacla silt that floods. Graham-Mebane Lake on Back Creek is the town's water supply. Old fields come back as loblolly, red cedar and sweetgum, with privet, honeysuckle and Bradford pear filling in along the roads.
Around Back Creek, Swepsonville Road and Big Alamance Creek, the properties we're usually called to look like this:
- Twenty- to eighty-acre cattle and hay farms off NC-87, NC-49 and Swepsonville Road reclaiming pasture from cedar and privet
- Subdivision lots and small commercial sites along the I-40/I-85 and Graham-Hopedale corridor
- Flat Iredell clay fields that need ditching and swales before they'll carry hay equipment
What trenching jobs look like around Graham
If you're near Big Alamance Creek or NC-49, odds are your situation is one we've already worked: twenty- to eighty-acre cattle and hay farms off NC-87, NC-49 and Swepsonville Road reclaiming pasture from cedar and privet, or conduit for low-voltage, fiber or irrigation mains.
The trenching approach for Alamance County ground is the same either way — look first, quote in writing, bring the right attachment, walk it with you when it's done.
Burlington, Haw River and Mebane are in the same loop as Graham for us — same crew, same pricing basis.
Why Graham property owners call A&R
We work with the trades in Alamance County — electricians, plumbers, well drillers, septic installers — and we dig to their spec and their schedule. If you don't have an installer, we can point you to one.
Call or text (336) 392-8138 to set up trenching in Graham. Tell us what's going in the ground and how far it runs, and we'll give you a price.
Trenching in Graham: questions
Do you call 811 before trenching?
Always. It's North Carolina law and it's free. Utilities have three business days to mark, so a little lead time on scheduling helps. 811 doesn't mark private lines — well lines, old septic, lines to outbuildings — so we ask about those and probe carefully where they might cross.
Can you trench for a septic line?
We dig the trench; the licensed septic installer lays the pipe and the county inspects it. Same with gas, electrical and water — we do the dirt work for the licensed trade. If you don't have an installer yet, we can usually recommend a couple we've worked with.
How far is A&R Land Services from Graham?
We're based in Greensboro, about 30 minutes from Graham. Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle trenching near Back Creek and Swepsonville Road?
Yes. We work throughout Graham and the surrounding Alamance County area, including properties around Back Creek, Swepsonville Road and Big Alamance Creek. If you're outside the town limits, send the address and we'll confirm it's in range.
What should I expect from a trenching job in Alamance County?
Gas line trenches dug for a licensed plumber is the most common version of it around Graham. 811 called, utilities marked, private lines discussed. We walk the route with you or the installer and set depth, width, start and end points. Roots, rock and hard clay along the route is the factor that moves the price most on Alamance County jobs, and we'll walk through it with you on site.