Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Drainage & Erosion · Guilford / Randolph County · 25 min from Greensboro

Culverts for Julian & Guilford / Randolph County

Driveway pipe sized to the water, set to grade, bedded in stone — no more washed-out entrance.

A driveway entrance in Julian is only as good as the pipe under it. A&R Land Services installs and replaces culverts throughout Guilford / Randolph County — new entrances, crushed pipe, undersized pipe that backs the ditch up — and we set every one to grade on stone bedding so it stays put. We're about 25 minutes away in Greensboro.

Guilford / Randolph County ditches carry more water than people think. A roadside ditch below a wooded hillside or a pasture can fill a 15-inch pipe in a thunderstorm, and that's when the entrance goes over the drive. We look at the drainage area above your Julian driveway before we pick a pipe size.

Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes
Freshly cleared and rough-graded backyard lot with track marks, mature trees left standing beside a house
Backyard lot cleared and rough graded, shade trees kept

Julian ground conditions and how they shape culverts

Jurisdiction matters out here because the county line runs through town; Guilford and Randolph have different erosion control processes, and we check which side a parcel falls on before we start. The slate-belt ground is kind to equipment — it carries a machine in weather that would stop us up north — but it needs seed and cover the same week it's graded. The Alamance Creek bottoms are the exception; we don't push grading down there until summer. Rock near the surface on the ridges can make trenching slow going.

Around Julian Airport, Troxler Mill Road and Julian Road, the properties we're usually called to look like this:

  • Hunting and timber land needing food plot edges, shooting lanes and farm roads
  • Horse properties along NC-62 needing fence lines mulched and paddocks leveled
  • Family home sites carved off the corner of a home tract, with a drive cut and a perc area cleared

What culverts jobs look like around Julian

A typical Julian call for culverts looks like this: Hunting and timber land needing food plot edges, shooting lanes and farm roads. We've handled that exact situation around Julian Road and Kimesville Road more times than we can count.

The other common one is Culverts buried in silt that need cleaning or resetting, which usually means a tighter work area and more care around what stays.

If your property is somewhere in between, send the address and we'll tell you which side of the line it falls on.

We also cover culverts in Burlington, Staley and Pleasant Garden, so if you've got property in more than one spot we can often batch the work.

Why Julian property owners call A&R

Being about 25 minutes from Julian means a culvert replacement is usually a single-day trip for us, not a two-day mobilization. That shows up in the price, and it means we can get to a washed-out entrance quickly after a storm.

For culvert installation and replacement in Julian and the rest of Guilford / Randolph County, call (336) 392-8138. Free estimates, properly sized pipe, and an entrance that holds.

Culverts in Julian: questions

How much does it cost to install a driveway culvert in NC?

The main drivers are pipe size and length, whether an old pipe has to come out, and how much stone the backfill and end treatments take. A short 15-inch HDPE pipe on a private drive is a half-day job. A 24-inch, 40-foot pipe on a state road with riprap ends and a full ditch reshape is a bigger day with a lot more material. We give a free written estimate after seeing the site.

What size culvert do I need for my driveway?

It depends on how much water the ditch carries, which depends on the drainage area above it. 15 inches is a common minimum on quiet roads; 18 and 24 inches are common where the ditch drains a larger area. On state roads NCDOT decides. On private property we size to the drainage area with a margin, because an undersized pipe is the most common reason an entrance washes out.

How far is A&R Land Services from Julian?

We're based in Greensboro, about 25 minutes from Julian. Guilford / Randolph County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle culverts near Julian Airport and Troxler Mill Road?

Yes. We work throughout Julian and the surrounding Guilford / Randolph County area, including properties around Julian Airport, Troxler Mill Road and Julian Road. If you're outside the town limits, send the address and we'll confirm it's in range.

What does culverts typically involve on a Julian property?

Crushed, rusted or collapsed driveway pipe replacement is the most common version of it around Julian. We look at the ditch, estimate the drainage area, check for utilities and figure out whether the road is state-maintained. If it is, we'll walk you through the NCDOT driveway permit and what size pipe they'll require. Ditch cleaning and reshaping needed upstream and downstream is the factor that moves the price most on Guilford / Randolph County jobs, and we'll walk through it with you on site.

Culverts in Julian, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate