Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Drainage & Erosion · Guilford / Alamance County · 20 min from Greensboro

Gibsonville Culverts

Driveway pipe sized to the water, set to grade, bedded in stone — no more washed-out entrance.

If the gravel at the end of your Gibsonville driveway ends up in the road after every storm, the culvert is the problem. We size the pipe to the ditch, set it right and rebuild the crossing so Guilford / Alamance County weather stops winning that fight.

Around Gibsonville, a lot of the older culverts are corrugated metal that has rusted through on the bottom. The pipe looks fine from the ends but the water is running under it, and the driveway above is slowly sinking into the void. We pull those and replace them with HDPE or concrete depending on cover and traffic.

Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes
Freshly cleared and rough-graded backyard lot with track marks, mature trees left standing beside a house
Backyard lot cleared and rough graded, shade trees kept

Gibsonville ground conditions and how they shape culverts

Most of our Gibsonville work is on the edges — rural residential lots along NC-61 and NC-100, small farms off Burlington Road that are being split up, and the ground around the old textile mill village where homeowners want wooded back lots opened up. The Guilford side is seeing subdivisions push out from McLeansville and Whitsett, so we clear a lot of one- to two-acre build lots there. On the Alamance side there are still working hay and cattle operations where the fence lines have disappeared into honeysuckle and we get called to mulch them back out.

Around Minneola Mill, Travis Creek and Burlington Avenue, the properties we're usually called to look like this:

  • Fence-line and hedgerow clearing on the Alamance side where honeysuckle has buried the wire
  • Flat Iredell clay pastures that need ditching and drainage before the owner can run equipment on them
  • One- to two-acre build lots on the Guilford side where subdivisions are pushing out from McLeansville and Whitsett

What culverts jobs look like around Gibsonville

One job we see over and over near Burlington Avenue: Fence-line and hedgerow clearing on the Alamance side where honeysuckle has buried the wire. That's textbook culverts work, and it's usually a one-mobilization job for us.

Out toward Eastern Guilford High School the pattern changes — more Farm lane and trail crossings over ditches and draws. The approach is the same, the time on site is what moves.

Either way, the first question we ask on a Gibsonville site walk is what the ground needs to do afterward, because that decides how far we take it.

Browns Summit, Burlington and Graham are in the same loop as Gibsonville for us — same crew, same pricing basis.

Why Gibsonville property owners call A&R

Every pipe we set in Guilford / Alamance County goes on stone bedding, gets backfilled with ABC stone in lifts and compacted, and gets its ends armored. That's more work than dropping a pipe in a trench and covering it with clay, and it's why ours don't settle or wash.

Get the pipe under your Gibsonville driveway fixed before the next storm takes the gravel with it. A&R is about 20 minutes away and ready to help.

Culverts in Gibsonville: questions

What size culvert do I need for my driveway?

It depends on how much water the ditch carries, which depends on the drainage area above it. 15 inches is a common minimum on quiet roads; 18 and 24 inches are common where the ditch drains a larger area. On state roads NCDOT decides. On private property we size to the drainage area with a margin, because an undersized pipe is the most common reason an entrance washes out.

Can you replace a crushed culvert pipe?

Yes, and it's one of the most common jobs we do. The excavator pulls the old pipe, we clean out the silt, cut the trench to the right grade, set new pipe on stone bedding and rebuild the drive over it. If the old pipe was undersized or set too high, we fix that at the same time.

How far is A&R Land Services from Gibsonville?

We're based in Greensboro, about 20 minutes from Gibsonville. Guilford / Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle culverts near Minneola Mill and Travis Creek?

Yes. We work throughout Gibsonville and the surrounding Guilford / Alamance County area, including properties around Minneola Mill, Travis Creek and Burlington Avenue. If you're outside the town limits, send the address and we'll confirm it's in range.

How do you approach culverts on Gibsonville ground?

Upsizing an undersized pipe that backs the ditch up is the most common version of it around Gibsonville. Gravel surface rebuilt over the crossing with a slight crown, edges feathered into the existing drive, and the road shoulder cleaned up. We'll check it after the first heavy rain. Whether an old pipe has to be removed and hauled off is the factor that moves the price most on Guilford / Alamance County jobs, and we'll walk through it with you on site.

Culverts in Gibsonville, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate