A&R Land Services installs culverts and driveway pipe in McLeansville — state road entrances, private drives, farm lanes and ditch crossings. We're only about 15 minutes from McLeansville, which keeps the mobilization cost down on what's usually a one-day job.
Most of the McLeansville culvert jobs we do are on state-maintained secondary roads, where NCDOT sets the minimum pipe size and length through the driveway permit. We'll tell you what to expect from the district office and we build the entrance to meet it, because an entrance that doesn't pass inspection is one you'll be paying for twice.



McLeansville ground conditions and how they shape culverts
East of Greensboro along US-70 and I-85, McLeansville is a wide stretch of rolling farm ground that's turning into subdivisions one field at a time. The high ground is Cecil clay, but pockets of Enon and Iredell show up around Mt. Hope Church Road and toward Gibsonville, and those spots are wet, slick and slow. Buffalo Creek and Reedy Fork both pass near here on their way to the Haw River, and the bottoms along them are Chewacla silt that floods in a hard rain. Fields that stopped being farmed grow up in loblolly first, then sweetgum and red cedar, with privet and honeysuckle underneath.
Around Frieden Church Road, Youngs Mill Road and NC-61, the properties we're usually called to look like this:
- Subdivision build lots along McLeansville Road and NC-61 needing pine thickets cleared and pads leveled
- Three- to ten-acre homesteads off Huffine Mill, Youngs Mill and Frieden Church Road with overgrown back acreage and lost fence lines
- Storm-damaged tracts where downed loblolly needs cleanup and the brush mulched
What culverts jobs look like around McLeansville
Most of our culverts work in McLeansville comes from two directions. First, subdivision build lots along McLeansville Road and NC-61 needing pine thickets cleared and pads leveled. Second, new driveway entrances on state roads and private roads.
Both show up regularly along NC-61 and Reedy Fork, and both are jobs we can usually walk, quote and schedule inside a couple of weeks.
Neighbors in Elon, Browns Summit and Greensboro call us for the same work; McLeansville sits right in the middle of that route.
Why McLeansville property owners call A&R
We handle the permit question up front. If your McLeansville driveway is on a state road, we'll tell you what NCDOT is going to require before we quote, so there's no surprise about pipe size or length after the fact.
Send us a photo of the ends of your McLeansville driveway pipe and we'll tell you whether it's crushed, undersized or just silted shut before we schedule the visit.
Culverts in McLeansville: questions
Why does my driveway wash out at the road every time it rains?
Usually one of three things: the culvert is too small for the ditch, it's set higher than the ditch bottom so water backs up and goes over the drive, or it's silted shut. Sometimes it's all three. A correctly sized pipe set at ditch grade with the ditch cleaned on both sides fixes it, and the gravel stays where it belongs.
Can you replace a crushed culvert pipe?
Yes, and it's one of the most common jobs we do. The excavator pulls the old pipe, we clean out the silt, cut the trench to the right grade, set new pipe on stone bedding and rebuild the drive over it. If the old pipe was undersized or set too high, we fix that at the same time.
How far is A&R Land Services from McLeansville?
We're based in Greensboro, about 15 minutes from McLeansville. Guilford County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle culverts near Frieden Church Road and Youngs Mill Road?
Yes. We work throughout McLeansville and the surrounding Guilford County area, including properties around Frieden Church Road, Youngs Mill Road and NC-61. If you're outside the town limits, send the address and we'll confirm it's in range.
What should I expect from a culverts job in Guilford County?
Entrances that flood or wash out every big storm is the most common version of it around McLeansville. 811 marks come first. Then the mini excavator removes the old pipe or cuts the new trench to grade, matching the fall of the ditch so water doesn't pond at the inlet. Permit requirements and distance from Greensboro is the factor that moves the price most on Guilford County jobs, and we'll walk through it with you on site.