A&R Land Services is a veteran and fireman owned crew preparing building pads throughout High Point and Guilford County. Homes, metal buildings, garages, slabs. Owner on the machine, laser on the grade, and a pad your foundation contractor won't have to fix.
Stripping is the step that gets skipped most often on Guilford County pads. Topsoil, roots and old brush rot under the fill and the pad drops. We take all of it off the footprint on every High Point job and reuse the topsoil elsewhere on the lot.



High Point ground conditions and how they shape building pads
Our calls here split into two kinds. On the north side off Skeet Club Road, Sandy Ridge Road and Johnson Street, people are building on the last wooded two- and three-acre pieces between older subdivisions, and those lots have thirty years of loblolly, sweetgum and privet on them. On the south and east sides along Main Street, Eastchester Drive and the I-74 corridor, the work is commercial — old furniture plant yards, rail-side parcels and warehouse sites where somebody wants the volunteer trees and Bradford pears knocked down before a survey crew or a buyer shows up.
Around Johnson Street, Rich Fork Creek and Willard Dairy Road, the properties we're usually called to look like this:
- Former furniture plant and warehouse parcels along Main Street, Eastchester Drive and the rail corridor needing brush cleared and rough grading before resale
- Small commercial outparcels along Wendover Avenue and I-74 that need a cleared, leveled pad before a developer will look at them
- Older subdivisions on the west side where privet and honeysuckle have taken over the fence lines between neighbors
What building pads jobs look like around High Point
A typical High Point call for building pads looks like this: Former furniture plant and warehouse parcels along Main Street, Eastchester Drive and the rail corridor needing brush cleared and rough grading before resale. We've handled that exact situation around Willard Dairy Road and Skeet Club Road more times than we can count.
The other common one is Metal buildings, pole barns, workshops and detached garages, which usually means a tighter work area and more care around what stays.
If your property is somewhere in between, send the address and we'll tell you which side of the line it falls on.
Neighbors in Archdale, Thomasville and Colfax call us for the same work; High Point sits right in the middle of that route.
Why High Point property owners call A&R
If the High Point lot also needs clearing, a driveway cut in, or a septic area opened up, we do it in the same mobilization as the pad. One estimate, one crew, one clean handoff to your builder.
Call or text (336) 392-8138 to get a free building pad estimate in High Point. Send the site plan if you have it and we'll come stake it.
Building Pads in High Point: questions
How much does it cost to build a house pad in NC?
The cost is mostly in the dirt. A pad on a flat lot where the fill comes from the same site is a day or two of machine time and the low end. A pad on a slope that needs several feet of imported fill compacted in lifts, with geotech testing, is a bigger project and sits well above that. We stake it, measure the cut and fill, and give you a written number before anything moves.
How high should a building pad be above grade?
High enough that water runs off it in every direction. A few inches above surrounding grade with a slight crown is typical for a crawl space home; a slab pad gets set a specific depth below finished floor so the stone and concrete land at the right height. Your builder's finished floor elevation is the number we grade to.
How far is A&R Land Services from High Point?
We're based in Greensboro, about 25 minutes from High Point. Guilford County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle building pads near Johnson Street and Rich Fork Creek?
Yes. We work throughout High Point and the surrounding Guilford County area, including properties around Johnson Street, Rich Fork Creek and Willard Dairy Road. If you're outside the town limits, send the address and we'll confirm it's in range.
How do you approach building pads on High Point ground?
Additions where the new footprint sits on unprepared ground is the most common version of it around High Point. We review the site plan, stake the footprint with working room around it, set a laser benchmark to the finished floor elevation, and work out cut and fill. Whether fill balances on site or has to be delivered is the factor that moves the price most on Guilford County jobs, and we'll walk through it with you on site.