Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Orange County · 50 min from Greensboro

Hillsborough Trail Cutting

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

A side-by-side loop, a path to the deer stand, a lane to the hay field you haven't reached in years — whatever the trail is for on your Hillsborough property, we cut it to that width and that purpose.

The woods around Hillsborough are mostly hardwood slopes with a privet and honeysuckle understory, which cuts cleanly. We route trails along the contour on Orange County slopes so they don't gully out after the first wet winter.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Hillsborough ground conditions and how they shape trail cutting

A good share of our Hillsborough work comes from the ten- to forty-acre tracts along Dimmocks Mill Road, Old NC-10 and St. Marys Road where Durham and Chapel Hill commuters are buying farmland and wanting a house site, a pasture and a view back out of it. South of I-85 the ground gets rockier as you head toward Efland and the Triassic edge. We also pick up right-of-way and utility access work near the Orange County line and overgrown mill-village lots around West Hillsborough.

Around Occoneechee Mountain, Seven Mile Creek and Churton Street, the properties we're usually called to look like this:

  • Small commercial parcels near the I-85/I-40 interchange needing rough grading and debris removal ahead of a sale
  • Older horse properties around Schley and Cedar Grove where privet and honeysuckle have taken the fence rows
  • Eno and Little River bottomland tracts that need brush cleared up to the buffer line and a usable trail cut to the water

What trail cutting jobs look like around Hillsborough

A typical Hillsborough call for trail cutting looks like this: Small commercial parcels near the I-85/I-40 interchange needing rough grading and debris removal ahead of a sale. We've handled that exact situation around Churton Street and Old NC-10 more times than we can count.

The other common one is UTV, ATV and dirt bike trails on recreational land, which usually means a tighter work area and more care around what stays.

If your property is somewhere in between, send the address and we'll tell you which side of the line it falls on.

We also cover trail cutting in Pittsboro, Roxboro and Chapel Hill, so if you've got property in more than one spot we can often batch the work.

Why Hillsborough property owners call A&R

We flag the route with you before the mulcher starts, so the trail goes where you want it and around the trees you care about. The estimate names the length, width, crossings and any gravel, and the number holds.

For trails, UTV loops and equipment lanes in Hillsborough, call (336) 392-8138. The owner routes it, cuts it and rides it with you.

Trail Cutting in Hillsborough: questions

Do you remove the stumps on the trail?

Stumps inside the corridor get mulched to grade — low enough that they won't catch a tire, a hoof or a boot. On stretches where you want bare dirt for gravel we pull them with the excavator. Most trail customers are fine with mulched stumps and a chip floor.

How wide should an ATV or UTV trail be?

Eight feet is the minimum for a side-by-side to pass comfortably, and ten feet gives you room on turns and lets two riders meet. Walking trails are fine at four to six feet. Equipment access for a tractor or truck wants twelve or more. We cut to the use and keep the turns gentle enough for whatever's riding it.

How far is A&R Land Services from Hillsborough?

We're based in Greensboro, about 50 minutes from Hillsborough. Orange County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near Occoneechee Mountain and Seven Mile Creek?

Yes. We work throughout Hillsborough and the surrounding Orange County area, including properties around Occoneechee Mountain, Seven Mile Creek and Churton Street. If you're outside the town limits, send the address and we'll confirm it's in range.

How do you approach trail cutting on Hillsborough ground?

Equipment lanes to back fields, timber and ponds is the most common version of it around Hillsborough. We walk the woods with you, lay out the trail with flagging tape, and adjust it for slope, drainage, keeper trees and creek crossings. If you want a loop, access to a stand or a lane to a field, that shapes the route. Total trail length and width is the factor that moves the price most on Orange County jobs, and we'll walk through it with you on site.

Trail Cutting in Hillsborough, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate