A side-by-side loop, a path to the deer stand, a lane to the hay field you haven't reached in years — whatever the trail is for on your Roxboro property, we cut it to that width and that purpose.
The woods around Roxboro are mostly hardwood slopes with a privet and honeysuckle understory, which cuts cleanly. We route trails along the contour on Person County slopes so they don't gully out after the first wet winter.



Roxboro ground conditions and how they shape trail cutting
Hyco and Mayo both have Duke Energy shoreline programs with buffer and clearing rules, and Person County applies its erosion program past an acre on top of that, so lake jobs start with a walk-through to flag the limits. We mulch the banks, keep the root mat, and stage silt fence before we cut. Helena flats around Roxboro are winter mud and go on the summer list; Cecil ridges and the slate-belt ground south of town dry faster. The drive from Greensboro is long enough that we group Roxboro jobs and bring everything we might need in one trip.
Around Hyco Lake, NC-57 and Hyco Lake Dam, the properties we're usually called to look like this:
- House sites on old homeplaces off Leasburg Road and Semora Road
- Hunting leases on timber tracts toward the Virginia line needing lanes, plots and roads
- Lots draining toward Lake Roxboro that must be cleared and stabilized under watershed rules
What trail cutting jobs look like around Roxboro
Around Hyco Lake Dam, the properties that call us for trail cutting tend to be house sites on old homeplaces off Leasburg Road and Semora Road.
Closer to NC-49 it's more often walking and running loops on wooded homesites — different layout, same machine, and the estimate reflects the difference honestly.
Roxboro isn't one kind of ground, and we don't price it like it is.
Milton, Durham and Hillsborough are in the same loop as Roxboro for us — same crew, same pricing basis.
Why Roxboro property owners call A&R
We flag the route with you before the mulcher starts, so the trail goes where you want it and around the trees you care about. The estimate names the length, width, crossings and any gravel, and the number holds.
For trails, UTV loops and equipment lanes in Roxboro, call (336) 392-8138. The owner routes it, cuts it and rides it with you.
Trail Cutting in Roxboro: questions
How wide should an ATV or UTV trail be?
Eight feet is the minimum for a side-by-side to pass comfortably, and ten feet gives you room on turns and lets two riders meet. Walking trails are fine at four to six feet. Equipment access for a tractor or truck wants twelve or more. We cut to the use and keep the turns gentle enough for whatever's riding it.
Will the trail turn into mud?
Not if it's routed right. A trail that runs straight down a slope on Piedmont clay becomes a gully; one that follows the contour and crosses slopes at an angle sheds water. We route for drainage, keep the mulch layer on the path, and put gravel on any stretch that's going to be wet no matter what — usually creek approaches and the bottom of climbs.
How far is A&R Land Services from Roxboro?
We're based in Greensboro, about 1 hour 15 minutes from Roxboro. Person County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.
Do you handle trail cutting near Hyco Lake and NC-57?
Yes. We work throughout Roxboro and the surrounding Person County area, including properties around Hyco Lake, NC-57 and Hyco Lake Dam. If you're outside the town limits, send the address and we'll confirm it's in range.
What does trail cutting typically involve on a Roxboro property?
Access routes to deer stands, food plots and hunting blinds is the most common version of it around Roxboro. A written plan with the trail's length and width, where crossings are, any gravel or culvert work included, and the price. Trails are quoted by the job after the walk. Access to the start of the trail from where we can unload is the factor that moves the price most on Person County jobs, and we'll walk through it with you on site.