Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Alamance County · 25 min from Greensboro

Trail Cutting for Burlington & Alamance County

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

Trail cutting in Burlington is as much routing as it is clearing. We flag the path with you, follow the contours so it drains, pick the creek crossings where the banks are low, and then mulch the corridor to a clean floor.

Burlington homesites on bigger lots often have a creek or a bluff at the back that the family's never actually visited. A walking trail down to it is a half-day job that changes how the property gets used.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Burlington ground conditions and how they shape trail cutting

Iredell clay rules the schedule. It's slick as grease when wet, cracks open in August, and will not grade cleanly until it's had a dry week. We watch the forecast and run track machines on it. Drainage work — swales, French drains, ditch cleaning — is a bigger share of the job in Burlington than anywhere else we work. Both city lakes are water supply, so the watershed overlays require buffers and limit impervious cover, and Alamance County erosion control covers disturbance past an acre outside city limits.

Around Stony Creek, Maple Avenue and Church Street (NC-62), the properties we're usually called to look like this:

  • Flat Iredell clay yards and fields that hold water and need swales, French drains and ditching
  • Former textile and hosiery mill parcels along the rail line and the Haw River overgrown with privet, kudzu and Bradford pear
  • Church and school properties with wooded land they want opened for expansion or parking

What trail cutting jobs look like around Burlington

Most of our trail cutting work in Burlington comes from two directions. First, flat Iredell clay yards and fields that hold water and need swales, French drains and ditching. Second, fire and emergency access through dense acreage.

Both show up regularly along Church Street (NC-62) and I-40 / I-85, and both are jobs we can usually walk, quote and schedule inside a couple of weeks.

Neighbors in Graham, Haw River and Saxapahaw call us for the same work; Burlington sits right in the middle of that route.

Why Burlington property owners call A&R

If the trail needs a culvert at the branch, gravel on the climb, or a wider lane for the tractor on one stretch, we do it in the same Alamance County trip.

Call or text (336) 392-8138 to set up a free trail cutting estimate in Burlington. We'll walk the woods with you and flag the route before we quote it.

Trail Cutting in Burlington: questions

How much does it cost to cut a trail through the woods?

Trails are priced by length, width and how thick the woods are, with creek crossings and gravel as the add-ons. A quarter mile of walking path through open hardwoods is a short day. A mile of ten-foot UTV loop through privet with two creek crossings and gravel on the climbs is a multi-day job. We flag the route with you and give a written number. Estimates are free.

Will the trail turn into mud?

Not if it's routed right. A trail that runs straight down a slope on Piedmont clay becomes a gully; one that follows the contour and crosses slopes at an angle sheds water. We route for drainage, keep the mulch layer on the path, and put gravel on any stretch that's going to be wet no matter what — usually creek approaches and the bottom of climbs.

How far is A&R Land Services from Burlington?

We're based in Greensboro, about 25 minutes from Burlington. Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near Stony Creek and Maple Avenue?

Yes. We work throughout Burlington and the surrounding Alamance County area, including properties around Stony Creek, Maple Avenue and Church Street (NC-62). If you're outside the town limits, send the address and we'll confirm it's in range.

What does trail cutting typically involve on a Burlington property?

UTV, ATV and dirt bike trails on recreational land is the most common version of it around Burlington. The mulcher follows the flags, taking brush and saplings to grade and working around the trees you're keeping. Low limbs that would catch a rider get cut. Larger trees on the route get a decision — route around or fell and grapple off. Trees on the route that need felling and handling is the factor that moves the price most on Alamance County jobs, and we'll walk through it with you on site.

Trail Cutting in Burlington, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate