Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Alamance County · 22 min from Greensboro

Trail Cutting for Elon & Alamance County

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

If you can't get to the back of your Elon property without a machete, we'll cut the route. Veteran and fireman owned, based in Greensboro, and trail work on Alamance County recreational land is some of the most enjoyable work we do.

Hunting tracts around Elon want trails that get you to the stand without walking through the bedding cover. We route those with the wind and the terrain in mind and keep the corridor just wide enough for a quiet walk or a UTV.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Elon ground conditions and how they shape trail cutting

The Haw River corridor and the Lake Burlington and Lake Cammack watersheds carry buffer and impervious-surface rules, so we keep mulch on the slopes and stay off the stream banks. Alamance County erosion control permits apply past an acre outside the town limits. Cecil ground here is reliable most of the year; the Enon pockets near Travis Creek need a dry spell before we grade them. Storm cleanup is common after summer thunderstorms drop pines in the neighborhoods west of campus.

Around Travis Creek, NC-100 and Haw River, the properties we're usually called to look like this:

  • Subdivision yards with storm-dropped pines needing cleanup and clearing
  • Hay and cattle farms north toward Altamahaw and Ossipee reclaiming pasture and fence lines
  • Haw River frontage lots inside the watershed buffers needing selective clearing

What trail cutting jobs look like around Elon

Around Haw River, the properties that call us for trail cutting tend to be subdivision yards with storm-dropped pines needing cleanup and clearing.

Closer to Elon University it's more often uTV, ATV and dirt bike trails on recreational land — different layout, same machine, and the estimate reflects the difference honestly.

Elon isn't one kind of ground, and we don't price it like it is.

We also cover trail cutting in Gibsonville, Haw River and Whitsett, so if you've got property in more than one spot we can often batch the work.

Why Elon property owners call A&R

A mulched trail in Elon is clean from day one — no windrow of brush along the edge, no stumps standing up, no burn pile smoldering by the path. Just a corridor through the woods with a chip floor.

Trail cutting in Alamance County starts with a walk through the woods. Get in touch and let's lay it out.

Trail Cutting in Elon: questions

Will the trail turn into mud?

Not if it's routed right. A trail that runs straight down a slope on Piedmont clay becomes a gully; one that follows the contour and crosses slopes at an angle sheds water. We route for drainage, keep the mulch layer on the path, and put gravel on any stretch that's going to be wet no matter what — usually creek approaches and the bottom of climbs.

Do you remove the stumps on the trail?

Stumps inside the corridor get mulched to grade — low enough that they won't catch a tire, a hoof or a boot. On stretches where you want bare dirt for gravel we pull them with the excavator. Most trail customers are fine with mulched stumps and a chip floor.

How far is A&R Land Services from Elon?

We're based in Greensboro, about 22 minutes from Elon. Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near Travis Creek and NC-100?

Yes. We work throughout Elon and the surrounding Alamance County area, including properties around Travis Creek, NC-100 and Haw River. If you're outside the town limits, send the address and we'll confirm it's in range.

What does trail cutting typically involve on a Elon property?

Equipment lanes to back fields, timber and ponds is the most common version of it around Elon. A written plan with the trail's length and width, where crossings are, any gravel or culvert work included, and the price. Trails are quoted by the job after the walk. Total trail length and width is the factor that moves the price most on Alamance County jobs, and we'll walk through it with you on site.

Trail Cutting in Elon, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate