Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Guilford / Alamance County · 20 min from Greensboro

Trail Cutting for Gibsonville & Guilford / Alamance County

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

A side-by-side loop, a path to the deer stand, a lane to the hay field you haven't reached in years — whatever the trail is for on your Gibsonville property, we cut it to that width and that purpose.

The woods around Gibsonville are mostly hardwood slopes with a privet and honeysuckle understory, which cuts cleanly. We route trails along the contour on Guilford / Alamance County slopes so they don't gully out after the first wet winter.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Gibsonville ground conditions and how they shape trail cutting

On Iredell ground we'll tell you straight: don't grade it wet. It turns to grease, ruts three feet deep and sets like concrete when it dries. We wait for a solid dry week and we use a track machine. Drainage work is a bigger share of the job here than in most towns — French drains, swales and ditch cleaning to get water off the flat clay and moving toward the creek. Since the town spans two counties, we check which erosion control office has jurisdiction before we start anything over an acre.

Around Lake Mackintosh (south), Travis Creek and NC-100, the properties we're usually called to look like this:

  • Small hay and cattle farms off NC-61 and Burlington Road being split for family home sites
  • Flat Iredell clay pastures that need ditching and drainage before the owner can run equipment on them
  • Fence-line and hedgerow clearing on the Alamance side where honeysuckle has buried the wire

What trail cutting jobs look like around Gibsonville

Most of our trail cutting work in Gibsonville comes from two directions. First, small hay and cattle farms off NC-61 and Burlington Road being split for family home sites. Second, horse trails and riding paths on farm property.

Both show up regularly along NC-100 and Boone Station Road, and both are jobs we can usually walk, quote and schedule inside a couple of weeks.

Neighbors in Elon, Browns Summit and Graham call us for the same work; Gibsonville sits right in the middle of that route.

Why Gibsonville property owners call A&R

We flag the route with you before the mulcher starts, so the trail goes where you want it and around the trees you care about. The estimate names the length, width, crossings and any gravel, and the number holds.

For trails, UTV loops and equipment lanes in Gibsonville, call (336) 392-8138. The owner routes it, cuts it and rides it with you.

Trail Cutting in Gibsonville: questions

How much does it cost to cut a trail through the woods?

Trails are priced by length, width and how thick the woods are, with creek crossings and gravel as the add-ons. A quarter mile of walking path through open hardwoods is a short day. A mile of ten-foot UTV loop through privet with two creek crossings and gravel on the climbs is a multi-day job. We flag the route with you and give a written number. Estimates are free.

Do you remove the stumps on the trail?

Stumps inside the corridor get mulched to grade — low enough that they won't catch a tire, a hoof or a boot. On stretches where you want bare dirt for gravel we pull them with the excavator. Most trail customers are fine with mulched stumps and a chip floor.

How far is A&R Land Services from Gibsonville?

We're based in Greensboro, about 20 minutes from Gibsonville. Guilford / Alamance County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near Lake Mackintosh (south) and Travis Creek?

Yes. We work throughout Gibsonville and the surrounding Guilford / Alamance County area, including properties around Lake Mackintosh (south), Travis Creek and NC-100. If you're outside the town limits, send the address and we'll confirm it's in range.

What does trail cutting typically involve on a Gibsonville property?

Fire and emergency access through dense acreage is the most common version of it around Gibsonville. The mulcher follows the flags, taking brush and saplings to grade and working around the trees you're keeping. Low limbs that would catch a rider get cut. Larger trees on the route get a decision — route around or fell and grapple off. Creek and wet crossings and whether they get stone or a culvert is the factor that moves the price most on Guilford / Alamance County jobs, and we'll walk through it with you on site.

Trail Cutting in Gibsonville, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate