Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Randolph County · 40 min from Greensboro

Trail Cutting in Ramseur, NC

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

A&R cuts trails through Randolph County woods without a pile of brush beside the path or a burn permit. The mulcher grinds the corridor to chips, the roots hold the clay, and your Ramseur trail is walkable before the trailer's hooked up.

Red clay climbs in Randolph County woods get slick under ATV tires. We put the climbs where the ground is firmest, angle them across the slope, and gravel the ones that are going to be wet regardless.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Ramseur ground conditions and how they shape trail cutting

Ramseur is a Deep River mill town, and the river is the first thing you deal with on any job here. The dam at Ramseur backs up Ramseur Lake through the middle of town, and the banks on both sides are steep slate-belt ground — Georgeville, Badin and Tatum silt loam that is shallow to rock and sheds water in sheets when it is bare. Above the river the land flattens out into old farm country on Cid and Misenheimer soils that stay wet in the flats. Sandy Creek comes in from the north. Idle fields along NC-22 and the Coleridge road have gone to loblolly and sweetgum with privet along every drainage.

Around the old Columbia Manufacturing mill, Jordan Street and Franklinville Road, the properties we're usually called to look like this:

  • Family farm house sites along NC-22 and toward Coleridge being cut out of pine stands that were pasture a generation ago
  • Ramseur Lake and Deep River lot owners wanting the understory thinned to the water without disturbing the bank
  • Poultry operations along US-64 needing house pads, gravel roads and field edges cleared

What trail cutting jobs look like around Ramseur

A typical Ramseur call for trail cutting looks like this: Family farm house sites along NC-22 and toward Coleridge being cut out of pine stands that were pasture a generation ago. We've handled that exact situation around Franklinville Road and Brooklyn Avenue more times than we can count.

The other common one is Horse trails and riding paths on farm property, which usually means a tighter work area and more care around what stays.

If your property is somewhere in between, send the address and we'll tell you which side of the line it falls on.

If you're just outside Ramseur — Franklinville, Siler City, Climax or anywhere between — you're still inside our regular range.

Why Ramseur property owners call A&R

The owner cuts every Ramseur trail himself. Clark is a veteran and a working firefighter, and he's laid out enough routes through Randolph County woods to know where a trail will hold and where it'll wash.

Open up your Ramseur property. Reach out to A&R Land Services for trail and access path cutting anywhere in Randolph County.

Trail Cutting in Ramseur: questions

Do you remove the stumps on the trail?

Stumps inside the corridor get mulched to grade — low enough that they won't catch a tire, a hoof or a boot. On stretches where you want bare dirt for gravel we pull them with the excavator. Most trail customers are fine with mulched stumps and a chip floor.

Can you cut a trail across a creek?

Yes. We pick the crossing where the banks are low and the bottom is firm, keep the clearing narrow inside the buffer, and either set stone for a ford or install a culvert with fill over it, depending on how much water runs and how often you need to cross it in the wet. The excavator and the dump trailer handle it on the same visit.

How far is A&R Land Services from Ramseur?

We're based in Greensboro, about 40 minutes from Ramseur. Randolph County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near the old Columbia Manufacturing mill and Jordan Street?

Yes. We work throughout Ramseur and the surrounding Randolph County area, including properties around the old Columbia Manufacturing mill, Jordan Street and Franklinville Road. If you're outside the town limits, send the address and we'll confirm it's in range.

What should I expect from a trail cutting job in Randolph County?

Fire and emergency access through dense acreage is the most common version of it around Ramseur. We walk the woods with you, lay out the trail with flagging tape, and adjust it for slope, drainage, keeper trees and creek crossings. If you want a loop, access to a stand or a lane to a field, that shapes the route. Creek and wet crossings and whether they get stone or a culvert is the factor that moves the price most on Randolph County jobs, and we'll walk through it with you on site.

Trail Cutting in Ramseur, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate