Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Chatham County · 50 min from Greensboro

Trail Cutting for Siler City & Chatham County

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

Wooded land in Siler City is a lot more fun with a trail through it. A&R Land Services cuts walking loops, UTV paths and equipment lanes across Chatham County with a forestry mulcher, leaving a chip floor you can ride the same day. We're about 50 minutes away in Greensboro.

Nearly every trail we cut in Chatham County crosses a creek or a wet-weather branch. On Siler City properties we place the crossing where the bottom's firm, keep the clearing narrow inside the buffer, and set stone or a culvert if you'll be driving it in the wet.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Siler City ground conditions and how they shape trail cutting

Chatham County runs its own sediment and erosion control program and requires a plan over one disturbed acre; around Siler City that mostly affects the commercial work. The Rocky River corridor carries stream buffers. Rock is the bigger practical issue — we probe pads before we quote excavation so nobody gets surprised. For pasture and brush work the slate ground is a gift: we've run mulchers here in January when the Triassic clay fifteen miles east was impassable.

Around US-64, Goldston and Loves Creek, the properties we're usually called to look like this:

  • Wooded one- to five-acre home lots in new subdivisions off the bypass that need lot clearing and pad prep over shallow rock
  • Old homeplaces with collapsed outbuildings and a half-acre of privet to clear before a sale
  • Former poultry and cattle farms along US-64 and US-421 being graded for contractor yards, storage and new housing

What trail cutting jobs look like around Siler City

One job we see over and over near Loves Creek: Wooded one- to five-acre home lots in new subdivisions off the bypass that need lot clearing and pad prep over shallow rock. That's textbook trail cutting work, and it's usually a one-mobilization job for us.

Out toward Bonlee the pattern changes — more Walking and running loops on wooded homesites. The approach is the same, the time on site is what moves.

Either way, the first question we ask on a Siler City site walk is what the ground needs to do afterward, because that decides how far we take it.

Seagrove, Staley and Ramseur are in the same loop as Siler City for us — same crew, same pricing basis.

Why Siler City property owners call A&R

Greensboro to Siler City is about 50 minutes, which keeps a half-day trail job worth doing and makes it easy to come back and add a loop or a spur later.

Send us an aerial with the route sketched in and a couple of photos of the woods. We'll give you a real number for cutting it in Siler City.

Trail Cutting in Siler City: questions

Can you cut a trail across a creek?

Yes. We pick the crossing where the banks are low and the bottom is firm, keep the clearing narrow inside the buffer, and either set stone for a ford or install a culvert with fill over it, depending on how much water runs and how often you need to cross it in the wet. The excavator and the dump trailer handle it on the same visit.

What areas do you cut trails in?

Greensboro and roughly an hour and twenty minutes out — the Triad, north to the Virginia line, west to Mount Airy and Elkin, south to Salisbury, Albemarle and Sanford, and east to Durham, Chapel Hill and Raleigh. Most of our trail work is on recreational and hunting land in the rural counties around that ring.

How far is A&R Land Services from Siler City?

We're based in Greensboro, about 50 minutes from Siler City. Chatham County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near US-64 and Goldston?

Yes. We work throughout Siler City and the surrounding Chatham County area, including properties around US-64, Goldston and Loves Creek. If you're outside the town limits, send the address and we'll confirm it's in range.

What does trail cutting typically involve on a Siler City property?

Access routes to deer stands, food plots and hunting blinds is the most common version of it around Siler City. We walk or ride the trail end to end before we leave. If a turn is tight or a stub stands up, it gets fixed on the spot. Access to the start of the trail from where we can unload is the factor that moves the price most on Chatham County jobs, and we'll walk through it with you on site.

Trail Cutting in Siler City, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate