Veteran & Fireman Owned · Land clearing, forestry mulching & grading · Greensboro, NC & the Piedmont TriadCall or text (336) 392-8138
Forestry Mulching & Land Management · Davidson County · 45 min from Greensboro

Trail Cutting in Welcome, NC

Walking trails, ATV paths and equipment access cut through the woods and left mulched.

A&R cuts trails through Davidson County woods without a pile of brush beside the path or a burn permit. The mulcher grinds the corridor to chips, the roots hold the clay, and your Welcome trail is walkable before the trailer's hooked up.

Red clay climbs in Davidson County woods get slick under ATV tires. We put the climbs where the ground is firmest, angle them across the slope, and gravel the ones that are going to be wet regardless.

Trail entrance cut from a gravel drive into the woods with brush mulched back
Trail opened off the gravel drive
Kubota SVL97-2 track loader with Fecon forestry mulcher head working through brush and saplings in a Piedmont hardwood stand
Fecon mulcher head on the SVL97 — one pass takes brush and saplings to chips
Forestry mulcher threading between mature oak trunks while clearing understory
Selective clearing — keeper hardwoods stay, everything under them goes

Welcome ground conditions and how they shape trail cutting

Welcome is the North Davidson community along Old US-52 between Lexington and Winston-Salem, best known for Richard Childress Racing and the vineyards on the hills west of town. The ground is Cecil, Appling and Pacolet red clay on the ridges with Enon and Mecklenburg dark clay in the mafic belt that runs through Midway and Arcadia. Swearing Creek and its branches drain the south side toward the Yadkin and Muddy Creek drains the north. This was dairy, tobacco and small-grain country, and the fields that fell out of production are in cedar, Virginia pine and sweetgum with honeysuckle through all of it.

Around NC-150, Childress Vineyards and Old US-52, the properties we're usually called to look like this:

  • Swearing Creek bottomland the owner wants cleaned up for hay or a pond
  • Vineyard and race-shop properties needing commercial brush clearing, lot grading and drainage
  • Old dairy and tobacco farms with pasture gone to cedar and Virginia pine

What trail cutting jobs look like around Welcome

Around Old US-52, the properties that call us for trail cutting tend to be swearing Creek bottomland the owner wants cleaned up for hay or a pond.

Closer to Midway it's more often walking and running loops on wooded homesites — different layout, same machine, and the estimate reflects the difference honestly.

Welcome isn't one kind of ground, and we don't price it like it is.

We also cover trail cutting in Lexington, Advance and Bermuda Run, so if you've got property in more than one spot we can often batch the work.

Why Welcome property owners call A&R

The owner cuts every Welcome trail himself. Clark is a veteran and a working firefighter, and he's laid out enough routes through Davidson County woods to know where a trail will hold and where it'll wash.

Open up your Welcome property. Reach out to A&R Land Services for trail and access path cutting anywhere in Davidson County.

Trail Cutting in Welcome: questions

Do you remove the stumps on the trail?

Stumps inside the corridor get mulched to grade — low enough that they won't catch a tire, a hoof or a boot. On stretches where you want bare dirt for gravel we pull them with the excavator. Most trail customers are fine with mulched stumps and a chip floor.

Will the trail turn into mud?

Not if it's routed right. A trail that runs straight down a slope on Piedmont clay becomes a gully; one that follows the contour and crosses slopes at an angle sheds water. We route for drainage, keep the mulch layer on the path, and put gravel on any stretch that's going to be wet no matter what — usually creek approaches and the bottom of climbs.

How far is A&R Land Services from Welcome?

We're based in Greensboro, about 45 minutes from Welcome. Davidson County is inside the radius we work every week, so there's no long-haul mobilization charge built into your estimate.

Do you handle trail cutting near NC-150 and Childress Vineyards?

Yes. We work throughout Welcome and the surrounding Davidson County area, including properties around NC-150, Childress Vineyards and Old US-52. If you're outside the town limits, send the address and we'll confirm it's in range.

What should I expect from a trail cutting job in Davidson County?

Access routes to deer stands, food plots and hunting blinds is the most common version of it around Welcome. A written plan with the trail's length and width, where crossings are, any gravel or culvert work included, and the price. Trails are quoted by the job after the walk. Access to the start of the trail from where we can unload is the factor that moves the price most on Davidson County jobs, and we'll walk through it with you on site.

Trail Cutting in Welcome, done right the first time.

Call, text, or send a few photos and the address. Clark walks the property with you and puts a real number on the work.

(336) 392-8138Request an estimate